- ZEBRA PRINTER DRIVER FOR MAC INSTALL
- ZEBRA PRINTER DRIVER FOR MAC SOFTWARE
- ZEBRA PRINTER DRIVER FOR MAC CODE
- ZEBRA PRINTER DRIVER FOR MAC MAC
- ZEBRA PRINTER DRIVER FOR MAC WINDOWS
Next, calibrate the printer to set the media type (paper type). Allow the printer to feed the paper and stop on its own. Approximately 3 feet of paper for Receipt paper will feed. After the fourth flash, release the button.Īpproximately 4 inches of paper will feed out for Labels. ***Note: the LED light will flash once, the first time, then two times on the second flash, three times on the third flash and finally four times on the fourth flash. Press and HOLD the Feed (circular) button on the front of the Printer, itself, for several seconds, until it flashes the Green status LED light 4 times in sequence. We highly suggest 2 separate printers if this is an often occurrence.***Ĭhange the paper in the printer to the proper type you will use Label or Receipt paper. ***IMPORTANT NOTE: To switch from Receipt printing to Label printing or vice versa using the same printer, you must reset the Printer's Factory default settings by following the steps below, EVERY TIME you switch. *NOTE: If the top is printing too close to the edge, make the following change:Ĭhange the Adjustment - Top to 0.05 inch (this is a positive value) Once complete, be sure to right click on the Printer again and choose Printer Properties - choose to Print a Test Page.
Go back to the Printing Preferences - Advanced Setup.Ĭhange the Adjustment - Left Position (-.05) Be sure to use a negative sign.Īfter making these changes, Click OK. *NOTE: If the label is off center (left/right) make the following change:
Set Paper Size to Width 4.00 x Height 4.00īe sure that the rotate180 degrees box is checked as well Use the following settings for Receipt paper:.Right click on the Printer and Choose Printer Preferences - Options tab. Inside your computer, not Design Manager, Go to the Printer (Devices and Printers).
ZEBRA PRINTER DRIVER FOR MAC CODE
Important: Always print a couple of Design Manager test labels and then test them using the Bar Code Scanner before printing a large run of labels. If the computer that is used to print the labels is also used for other printing then make sure that the correct printer is selected the next time you print a non-label document.ĥ.
ZEBRA PRINTER DRIVER FOR MAC WINDOWS
*Some versions of Windows do not have a default paper size and therefore the Setup button will need to be used every time labels are printed. These settings can be changed in the Start menu of your Windows operating system by selecting Printers and Devices. Printer Configuration: Please see below for the proper settings needed to print Receipts or Labels. The Use Receipt Printer box must be checked if you are printing receipts to the Zebra printer.Ĥ. Go to G/L - Company Information window -A/R/Showroom tab.
ZEBRA PRINTER DRIVER FOR MAC SOFTWARE
The following setting must be changed in the Design Manager software if you are printing receipts using the Zebra printer. The Use Label Printer box must be checked if you are printing labels to the Zebra printer.ģ. Go to G/L - Company Information window - Inventory tab. The following setting must be changed in the Design Manager software if you are printing labels using the Zebra printer. In the Drop down for Driver find the GC420d (without the EPL)Ģ. Right click on the printer and choose Printer Properties.
Go to the printer on your Computer - Devices/Printers. If this driver is the GC420d (EPL) driver, you MUST change this driver to the GC420d driver (name should not include EPL).
ZEBRA PRINTER DRIVER FOR MAC INSTALL
Upon plugging the Zebra printer in, the computer may prompt you to download and install its own driver. **NOTE - If you are using the Zebra LP2844 or LP2824 printer, please see the following article here.ġ.
ZEBRA PRINTER DRIVER FOR MAC MAC
*NOTE - This printer does not install on Mac computers. Setup and Installation for the Zebra Receipt/Label Printer Model # GC420d
0 kommentar(er)
